What could be the dir 300nrub7 password. Hard reset to factory settings

It is gaining more and more popularity. And this is not surprising, because it is very convenient way for connecting to the Internet and linking various devices, because no need to use wires.

But, using Wi-Fi network Well, don't forget about her safety. If you still haven’t set a password for Wi-Fi or it’s too simple, perhaps a neighbor’s child has already hacked into your network and is using the free Internet for his own pleasure.

Of course, maybe you are a very kind person and you don’t feel sorry for anything for your dear neighbors, but then you shouldn’t complain that your favorite sites have started to load poorly.

If you still decide to secure your network, let's figure out how to set a password for Wi-Fi.

Where is the Wi-Fi password set?

Router (router) is the most common device when used Wi-Fi technology, so we will consider how to set a password on this particular device.

Now there are many router manufacturers on the market (D-Link, TP-Link, Zyxel, Asus, etc.) and even more various models these devices. Therefore, in this article we will not consider setting a password for all these models, but will analyze this procedure using the example of one of the popular routers D-Link DIR-300.

Settings for most modern wireless routers open using an Internet browser. This can be done on a computer, laptop, tablet or any other device that is connected to the router using wires or wireless communication.

It is advisable to perform this procedure on a device that is connected to the router via cable. The fact is that if you are connected via Wi-Fi, when you change the password, you will be disconnected from the network and you will have to go into the settings again.

In order to open the settings we need, we need to enter the IP address of the device in the address bar of the browser. Most manufacturers use standard IP addresses, but some may have their own specific address.

The most common router IP addresses:

• 192.168.0.1
• 192.168.1.1
• 192.168.2.1
• 10.0.0.1
• 10.0.1.1

If one of these addresses does not suit you, you can find it in several ways:

1. Look at the router case. Typically, manufacturers write the IP address of the router interface on a sticker on the bottom of the device.
2. Study the instructions or CD that were included.
3. Search the Internet for information on your router model.

It is possible that you have a non-standard IP address. In this case, you need to find out this address from the person who set up the router for you or reset the device to factory settings.

Login to router settings

Once you have determined which IP address is suitable for your device, enter it in the address bar of the browser.

If the connection to the router is successful, a window for entering your username and password should appear.

For most routers, the default username and password is “admin”. The D-Link DIR-300 is no exception. Therefore, you need to enter this word in both fields and click on the “Login” link.

If after these steps you are unable to enter the device settings, then either your router has different login data, or these data have been changed.

If you do not know the name and password to log into the device, then there are 2 options:

1. As in the case of the IP address, look at the case, read the instructions, search the Internet.
2. If the first step does not help, then you need to reset the router to standard settings using a special button on the device.

Setting a Wi-Fi password

After you have entered the router interface, find the “Security Settings” item in the “Advanced Settings” section. In the settings of other router models, the menu will look different, but similar items can be easily found at keywords wi-fi and security.

On the “Security Settings” page you need to set the following items:

• Network authentication
• PSK encryption key
• WPA encryption

In the “Network Authentication” field, you need to select which authentication technology will be used to protect your Wi-Fi network. WPA2 is currently the most safe method authentication for wireless network. Therefore, it is recommended to choose this particular item to reliably protect your wifi.

You should not be careless when choosing a password. The password must be quite complex, consisting of letters in different cases and numbers. It is desirable that it be some kind of meaningless set, and not specific words. This combination is harder to crack, and you don't have to remember it. Write it down somewhere and use it when connecting new devices to your wireless network.

The next step is to set up WPA encryption. To do this, you need to select an encryption algorithm in the “WPA encryption” field. It is recommended to choose AES, because it is one of the most reliable.

After entering all the parameters, click the “Change” button to save the settings. After changing the settings, most routers require a reboot. Therefore, most likely, you will be disconnected from the network and you will have to enter the password again.

Checking Wi-Fi operation

After rebooting the router, you will need to reconnect to the network on all devices and enter New Password.

If an error occurs when connecting, then most likely your device still has the old settings for connecting to wifi. To fix this problem, you need to remove your network from the list of connections and search for access points again. After your network appears in the list again, connect to it and enter a new password.

Router D-Link DIR 300 NRU - updated model previous version DIR 300. All network devices the specified brand are different good quality, an attractive and simple interface and, most importantly, a reasonable price. Let's find out what's so special about it this model with the most common modifications B5 and B7, how to install it for home use and, if necessary, flash the device.

The router is often used for a home network

This router differs from the previous model by supporting the 802.11n standard. IN this device the maximum speed is up to 150 Mbit/s, which is quite enough for home use. Externally, the router looks quite standard; the interface provides 4 LAN ports for creating local network, 1 WAN port, reset button to return to factory settings.

Thanks to the external location of the antenna, the device provides optimal Wi-Fi signal coverage. The router is quite easy to configure or reflash for any subscriber, which makes it even more attractive among other models of network equipment. It also has its own twist - in addition to standard functions, it is possible to turn the connection on or off according to a schedule.

Setting up the router

To install the equipment and configure Wi-Fi, you should follow these steps:

• Enter the device settings interface - to do this, enter your IP address in the address bar of the browser (in most cases this is 192.168.0.1), after which you need to enter the word admin in the login field, leaving the password line blank.

Note. These actions will give results if the D-Link DIR router has not been configured before. If you need to re-configure, return it to its original state - before starting the parameters, hold down the reset key for 20 seconds, after which it will return to factory settings.

• To establish a Wi-Fi connection, select the section with the same name in the menu and select the main settings tab.
• In the window that appears, enter the data to activate the connection - network name, country where you are, channel and type of wireless mode.

Setting up an Internet connection

To directly set up a network connection, you need to go to the “Network” menu, to the “Connections” tab. If you need to create new parameters, it is advisable to select the “Add” button and fill in the data in the window that appears - their content depends on the provider. For each type of connection PPPoE, PPtP, NAT, you need to enter certain data that is in the contract from the service provider - using the form, you can sequentially enter all the necessary information.

You can check the connection status on D-Link DIR in the “Status” section, “Network Statistics” tab.

Setting a password

In order to secure your network, set a key that you will need to enter to connect to the Internet. This is done as follows:

• In the Wi-Fi menu, select the “Security Settings” tab.
• Check the box to enable WEP, after which information for setting a password will appear.
• In the list of network authentications, from the drop-down list, select the WPA-PSK/WPA2-PSK mixed encryption type - it is the most reliable for protecting the network from hacking.
• On the next line, enter the access key - make it complex enough so that unauthorized users cannot connect to your connection.

Additionally, it is advisable to secure not only the network, but also the router configuration menu itself by changing the standard login and password data to your own combinations. This is done like this:

• Go to the “System” section, open the “Administrator Password” window.
• Enter new combinations to access the settings, after which you will need to re-enter the settings menu using the newly set login and password.

Saving changes

In the router settings there is a separate menu for saving changes or returning to factory settings; it is located in the “System” section, in the “Configuration” line. Here you can save the changes made, return to the initial settings, or save a file with current data in order to restore the connection later, if necessary.

Installing new firmware

If you want to update software router, do the following:

• Find and download from world wide web firmware file, the main thing is to choose the right software version, focusing not only on the router model number, but also on the hardware revision of the device, the details of which are written on back side router in the form of an H/W combination. There are different versions - B2, B5, B7 and others, they all differ from each other.
• Go to the router menu through a browser using the IP address.
• Open the “System” section, select the “Software Update” tab.
• A line will appear in the window to indicate the path to the file new firmware for hardware revision B5, B7. Find it on your computer, then click “Update”.

Thanks to the above steps, you can install the D-Link DIR 300 NRU router, configure it to work with the Internet and distribute a signal via Wi-Fi, and, if necessary, change or update its firmware for the correct operation of the equipment. As you can see, all this is done quite simply and easily, the process will not take much of your time.

In this manual, we will look in detail at all the steps that will help you configure the D-Link DIR-300 NRU Wi-Fi router hardware revision B7 for “ Home Internet Beeline." The guide will cover the following steps:

• Preparation for setup, connecting the router, information about updating the firmware, whether it is necessary to do it.
• The most common mistakes made when setting up a router.
• Setting up l2tp beeline connection on DIR-300 rev.B7.
• Setting up a wireless network, how to set a password for a Wi-Fi network.
• Setting up Beeline TV - digital television IPTV.

The process of setting up a router itself is not something that absolutely any user could not handle if they had competently and thoroughly written instructions. This is exactly what I try to write. Let's go!

Update: If your router has firmware 2.5.11 or 2.15.19 (generally 2.5.x), and the settings interface is similar to the screenshot below, use these instructions: .

Connecting the router to the computer, preparing for setup, how to flash the router and is it worth it?

Connecting the D-Link DIR-300 B7 Wi-Fi router is not difficult: just connect the Beeline cable to the Internet port on the back of the router, and connect one of the LAN ports with a cable to a similar connector on the computer or laptop from which the setup will be done. Plus turn on the power to the router. By the way, if you do not plan to flash the router (more on this later), then, in principle, all steps to configure the device can be performed via Wi-Fi - from a tablet or even a phone.

Now about D-Link firmware DIR-300 B7: if for some other models of D-Link routers I recommend updating the firmware, then routers of this modification, as a rule, usually work properly without this process. This way, you can complete all the router settings and turn to the firmware update method only if any problems arise, such as:

• Frequent spontaneous disconnections of the connection, which can only be “cure” by rebooting the router.
• Low speed Internet via Wi-Fi, the router “cuts” the speed.
• Other problems of unknown origin.

Penultimate: if you have already tried to configure your DIR-300 B7, but it did not work, reset the router to factory settings before continuing. To do this, with the router's power on, press and hold the Reset button on the back of the router for 10-15 seconds, then release it. It will take another 30 seconds to reboot the router with factory settings.

And lastly: before setting up, disconnect the Beeline connection on the computer that you use to access the Internet. And do not connect in the future - after configuration, the router itself will establish this connection and after that distribute it over the local and wireless Wi-Fi network to all devices. Otherwise, if you do not disable this connection, you will have a question about why there is Internet on the computer, but it connects via Wi-Fi, but without access to the Internet. And I'm very tired of answering this question.

Setting up l2tp beeline connection on DIR-300NRU B7

The main step when setting up any wireless router (Wi-Fi router) - correctly configure the connection parameters in it. This is what we will do - in our case it is DIR-300 B7 and the L2TP connection type used in Beeline. So let's get started.

Launch your favorite browser and enter 192.168.0.1 in its address bar. The next thing you will see is a username and password request to enter settings D-Link router DIR-300 NRU B7. The standard values ​​are admin and admin, here and there.

After entering the correct data, you will find yourself on the main router settings page. However, we won’t dwell on it: at the bottom of the “admin panel”, select the “Advanced settings” link.

On next page, in the “Network” item, click on the “WAN” link, and then click the “Add” button, not paying attention to the connection that is already in the list. Now you are on the Internet connection settings page, here you need to enter the correct parameters for the Beeline provider.

The fields should be filled in as follows (for those not mentioned here, the values ​​should not be changed or are not required):

• Connection type- L2TP + Dynamic IP
• Username- Your login for accessing the Beeline Internet
• Password- Your password for Internet access
• VPN server address- tp.internet.beeline.ru

Basically, that's all that needs to change. After that, click “Save”. After this, you will find yourself on a page where the newly created connection will be displayed in the “Broken” state. Also, the light at the top right will blink and the number one will be displayed: if you click on it (and this should be done), you will be asked to save the device configuration again - click “Save”.

Now just refresh the current page with the list of connections and, if you have not made any mistakes, and the Beeline Internet on the computer itself is disabled, you will see that the connection status has changed from “Broken” to “Connected”, which is what we needed.

l2TP Beeline connection is connected and working

Now the computer from which the setup is being done has full access to the Internet via the local network, and if you connect via Wi-Fi from another device, you will also have access to the Internet. However, don't rush to check. First, it is better to finally configure the router, namely the parameters of the wireless Wi-Fi network.

Setting up Wi-Fi on DIR-300 B7

In order to configure Wi-Fi on the DIR-300 B7, return to the advanced settings page and in the “Wi-Fi” item select “Basic settings”.

On this page you can configure the following settings:

• SSID(point name Wi-Fi access) - enter the desired name in English characters. This name will allow you to distinguish your wireless network from neighbors. By default (and recommended) it is visible to everyone within the access point's range.
• Country- network standard. The default is " Russian Federation", but I recommend changing to US. Some devices do not see or do not connect to a point with the Russian Federation region. Everyone without exception is connected to the USA.

The remaining parameters can be left unchanged. Save your settings. Now in the “Wi-Fi” item, click the “Security Settings” link.

• Network authentication- WPA2-PSK
• PSK encryption key- desired password for your wireless Wi-Fi network required to connect to it. Must consist of at least 8 Latin characters and/or numbers.

Save all the settings you have made. The router is ready to use.

Setting up IPTV Beeline (Digital TV via router)

In order to set up Beeline television on DIR-300NRU B7, just go to home page router settings (Quick setup) and click on “IP television”. In the next step, you will be asked to select the port on the router to which you will connect the Beeline set-top box. Select the appropriate one and save the settings. Ready.

If something refuses to work for you, write comments. If everything works, write too (I will be pleased) and share the instructions in social networks- this will make it easier for others to find it.

Setting up the DIR-300/NRU/B7 router

Connecting Wi-Fi router D-Link DIR-300 NRU rev. B7

The newly purchased and unpacked router is connected as follows: we connect the provider cable (in our case, Medialan) to the yellow port on the back of the router, signed Internet. Included cable blue plug one end into any of the four remaining sockets of the router, the other into the connector network card Your computer. We connect power to the router and wait until it boots up and the computer determines the parameters of the new network connection (don’t be surprised that it is “limited”; that’s how it’s supposed to be).

Note: when setting up the router, do not use the Medialan connection you have on your computer to access the Internet. It should be disabled. Subsequently, after setting up the router, it will also no longer be needed - the connection will be established by the router itself.

It would also be a good idea to make sure that in the local network connection settings for the IPV4 protocol the following parameters are set: obtain an IP address and addresses DNS servers automatically. To do this, in Windows 7, click on the connection icon at the bottom right, select “Network and Sharing Center” shared access", then change the adapter parameters, right-click on "Local Area Connection - Properties", and make sure that no static addresses are registered there. In Windows XP, these same properties can be viewed in the Control Panel - network connections. It seems that I have taken into account the main reasons why something may not work. Let's move on.

Setting up a connection in DIR-300 rev. B7

The first step to configure PPOE (Medialan works using this protocol) on the D-Link DIR-300 is to launch your favorite Internet browser ( Internet Explorer, Google Chrome, Mozilla Firefox, Safari on Mac OS X, etc.) and go to the address 192.168.0.1 (enter this address in the browser address bar and press enter). As a result, we should see a request for a login and password to enter the admin panel of the DIR-300 B7 router.

Login and password for DIR-300 rev. B7 The standard login is admin, the password is the same. If for some reason they do not fit, then perhaps you or someone else changed them. In this case, you can reset the router to factory settings. To do this, press and hold the RESET button on the back of the router with something thin (I use a toothpick) for 5 seconds. And then repeat the first step.
After entering your login and password, we will be taken to the settings menu of the D-Link DIR-300 rev router. B7

D-Link DIR-300 rev. B7 - administration panel
Here we need to select “Advanced settings”, after which you will see a page that will display the model of your Wi-Fi router, firmware version and other information.
IN top menu select “Network” and get to the list of WAN connections.

In the image above there is one WAN connection in this listing. Click on the WAN connection, you should have the following settings: connection type (Dynamic IP), you also need to check the box - Obtain DNS server address automatically. The Mac address will need to be cloned, because... There is a link to mas addresses. Click save.

After saving the WAN settings, click the add button in the lower right corner and get to the main WAN settings. This time we select PPPoE in the “Connection type” field. Then, instead of the standard connection name, you can enter any other name (for example, I have Medialan), in the “Username” field we enter your login from the Internet Medialan, in the password and password confirmation fields, respectively. Check the Keep Alive box and click “Save”. On the next page, where the newly created connection will be displayed, we will again be asked to save the configuration. Save.

Now, if all the operations above were performed correctly, if you did not make a mistake when entering the connection parameters, then when you go to the “Network” menu to the “WAN” tab, you should see the following joyful picture:

Pay attention to the checkbox in the “Default Gateway” item; the default should be the PPPoE connection you created. If all three connections are active, then this indicates that the most basic for D-Link settings DIR-300 NRU rev. We have successfully completed B7, and we can move on to the next step.

Setting up a WI-FI connection DIR-300 NRU B7

In general, you can use a wireless Wi-Fi connection immediately after connecting the router to the network, but in most cases it is useful to configure some of its parameters, in particular, set a password for the Wi-Fi access point so that your neighbors do not use your Internet. Even if you don’t mind, this can affect the speed of the network, and the “brakes” when working on the Internet will most likely not be pleasant for you. Go to the Wi-Fi tab, basic settings. Here you can set the access point name (SSID), it can be anything, it is advisable to use the Latin alphabet. After this is done, click change.

Now go to the “Security Settings” tab. Here you should select the type of network authentication (preferably WPA2-PSK, as in the picture) and set a password for your point WiFi access— letters and numbers, at least 8 characters. Click “Change”. Done. Now you can connect to a Wi-Fi access point from any device equipped with an appropriate communication module - be it a laptop, smartphone, tablet or Smart TV.

UPD: if it doesn’t work, try changing the router’s LAN address to 192.168.1.1 in settings - network - LAN.

What is needed for Medialan TV to work? In order for IPTV from Medialan to work through the router, go to the first page of the DIR-300 NRU rev settings. B7 (to do this you can press quick setup in the lower right corner) and select “IPTV Setup Wizard”. All that remains is to select the port to which you will connect IPTV set-top box. Click change.

That's probably all, don't forget to save your router settings!