Instructions for restoring Kingston flash drives. The flash drive says the disk is write protected. What could be the signs of life of a USB drive?

Kingston flash drives are distinguished by their reliability and long service life, but they are also not protected from various failures. Sometimes the drive actually “dies” and it is not possible to restore it. More often there are situations when a flash drive can be brought back to life using a special firmware utility.

Most often, Kingston dt100g2 and datatraveler flash drives break.

Is it possible to recover a flash drive?

Signs that the drive can be restored:

• When you connect a flash drive, a notification appears that a new device has been detected.
• The system prompts you to format the removable disk.
• The drive does not open, but is shown in Explorer.
• Errors occur when reading and writing data.

These problems can be eliminated by flashing the controller or formatting the media, but if there is important information on the flash drive, then you should try to “pull it out” before performing any recovery procedures. Use to extract a recovery program like Recuva or so as not to lose the necessary files.

Searching for a program to flash the controller

To restore you will need special utility for Kingston flash drive. To avoid mistakes and download the correct program, you need to know the model of the drive controller.

Method 1

You can view the necessary information on the website flashboot.ru in the iFlash section, using the VID and PID values ​​of the flash drive as a filter.

1. Connect the drive to your computer.
2. Open the device manager (right-click on the “Computer” icon - Manage).
3. Find "USB Mass Storage Device".
4. Right click and open properties.
   
5. Go to the Details section and select the Hardware ID property.

Method 2

Another way to get the information you need is to download Flash program Drive Information Extractor and click the “Get Data” button. The report will contain the lines “VID” and “PID”; use their value to find a utility that can correctly restore the Kingston Datatraveler flash drive.

You can download the program in the “Files” section on the website flashboot.ru. If the utility is not here, try to find it on other web resources.

Recovery utilities

You can find the program you need without a controller model - just type in the search engine the request “kingston recovery utility”. In the results you will see several utilities, among which there will certainly be programs such as Phison Preformat, AlcorMP AU698x RT, etc.

The problem is that Kingston flash drive recovery programs only work if they are compatible with the controller installed in the drive. Therefore, if you download the first repair utility you come across, it may not detect the connected media.

When required program found, you can begin to restore it. Be sure to look at the instructions, which should be packaged in the archive along with the recovery utility - perhaps the program has a special operating procedure. The general recovery procedure looks like this:

You don’t need to do anything else: the program will automatically correct errors and return the flash drive to a working state. This completes the restoration of the Kingston flash drive; If the controller firmware did not help resolve the problem, then the cause of incorrect operation should be sought among hardware faults.

Hi all! It’s not for nothing that I decided to write an article about how to flash a flash drive – I have experience. Yesterday I restored my flash drive Kingston DT Elite 3.0 16GB. Everything worked out, and I thought, why not write similar instructions, and tell me what to do and how to do it, in order to give the flash drive a new life :).

Nowadays, probably every house has a flash drive and very rarely just one. It is convenient to transfer information onto them, they are beautiful and, moreover, in lately not expensive. But very often USB drives fail. If we talk about why this happens, then we ourselves are in first place. you always do safe removal flash drives? So I rarely do. There may, of course, be other reasons why flash drives simply “die”.

One point needs to be clarified here. It happens that the flash drive really “dies”. In this case, it is impossible to restore it. At least at home. But if the USB drive shows at least some signs of life when connected to the computer, then you can try to restore its operation using the controller firmware.

What signs of life might there be? USB storage?

• When you connect the flash drive to the computer, the computer signals that the device is connected - that’s good.
• At Windows connection ask to format the removable drive (but during the formatting process there are problems and errors such as “Windows cannot complete formatting”).
• The flash drive is detected and visible in Explorer, but when you try to open it, the message “Insert disk...” appears.
• Errors occur when copying information.
• Very slow speed recording/reading information.

If there is a flash drive valuable information , then you can try to restore it before and after the firmware. This can be done using different programs. I advise Recuva, here is the article but there are many other good programs.

If the information is very valuable, then it is better not to do anything yourself so as not to make it worse. Contact special service centers who are engaged in information recovery.

Let's now look at the entire process of flashing the controller on real example, using my Kingston DataTraveler Elite 3.0 16GB flash drive as an example. My flash drive broke down. It’s interesting. I needed to upload files to it and delete those that had already been recorded. I connected it to the computer and started deleting the folder. But the folder was deleted very slowly. I unplugged and plugged this flash drive back in, a message appeared that the disk needs to be formatted “Before using the disk...”.

Since it was not on the flash drive Important files, I didn’t hesitate to start formatting.

But the process itself lasted a very long time and never ended, I forcibly stopped it. The message “Windows could not complete formatting” may also appear.

But still, I formatted it, the tenth time, and only in FAT 32. After which the USB drive was detected normally and I was even happy. But that was not the case. I started copying files onto it, and the recording speed was approximately 100 kb/s. I decided to flash it, which I did.

Determining the VID and PID of the USB controller

First we need determine VID and PID. This is data about the model and manufacturer of the controller, which is located in our drive. Using this data we will look for a utility for the firmware. There are many different programs, with which you can determine the VID and PID. I recommend the utility Flash Drive Information Extractor You can download it from the link.

Connect the USB flash drive to your computer and run the Flash Drive Information Extractor program (extract the program folder from the archive and run the GetFlashInfo.exe file).

Click the button at the top of the program “Get data about the flash drive”.

The program will give us the result. We look at the information that is located opposite VID and PID.

You can copy these numbers, or leave the utility window open, we will now need the received data.

We are looking for a utility for flashing a flash drive

Based on the VID and PID data, we need to find the utility with which we will flash the controller. There is a good website flashboot.ru, which contains a database of flash drives and utilities for their recovery.

In the search results we look for a flash drive similar to ours. The list may include devices from other manufacturers. They just have the same controller, it was identified by VID and PID. You may have noticed that I have a 16 GB flash drive, but in the list I highlighted 32 GB. I think there's nothing wrong with that (just where the name of the utility is not indicated on 16 GB). You try to choose a more similar device from the list.

We are interested in the field UTILS(utility), copy its name in full.

Unfortunately, the utility that I need was not found on this site. Perhaps you will have better luck and you will see something in the search results. Download the utility to your computer.

But I didn’t stop there and started Googling. I just asked “SK6221 MPTool 2013-04-25” and found this utility on some other site. If you have the same flash drive, then this utility is . True, the name of the archive is different, but this did not stop me from successfully curing my flash drive.

USB drive recovery process

Disconnect the flash drive. Extract the folder with the utility from the archive and run .exe file. In my case it is the MPTool.exe file. Also look at the text file readme.txt. Perhaps there are instructions there, or a link to a site with instructions. If the instructions are in English, then translate it using the same translate.google.ru.

I'll tell you how I did it (you just may have a different utility and everything may be different there, but it shouldn’t be very different).

The utility is running. We connect the flash drive. I have information about the flash drive in two lines in the program. Press the button Start. In my case, the yellow strip signaled the firmware process. We are waiting.

When the process ended, I saw a green color, everything seemed to be fine.

A Windows message should immediately appear asking you to format the disk. But most likely nothing will work out the first time. Unplug the flash drive and plug it back in. The driver should be installed and the removable drive should appear in Explorer. You can format it.

I checked the recording speed, everything is as it should be for USB 3.0, everything is fine!

You need to be prepared for the fact that the actions may differ from those I described. And not everything can work out the first time. The main thing is not to give up and everything will work out!